View MAX5128_342030.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-3929; Rev 0; 1/06
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package
General Description
The MAX5128 nonvolatile, single, linear-taper, digital potentiometer performs the function of a mechanical potentiometer, but replaces the mechanics with a simple 2-wire digital interface. The MAX5128 performs the same function as a discrete potentiometer or variable resistor and features 128 taps and 22k end-to-end resistance. The MAX5128 also features an ultra-small, 2mm x 2mm DFN package and low 0.5A (typ) standby supply current, making this device ideal for portable applications. The MAX5128 operates from a +2.7V to +5.25V power supply. An integrated nonvolatile memory recalls the programmed wiper position of the digital potentiometer. A simple 2-wire up/down interface programs the wiper position. The digital potentiometer provides a low 5ppm/C ratiometric temperature coefficient and is specified over the extended -40C to +85C temperature range.
Features
Ultra-Small, 2mm x 2mm, 8-Pin DFN Package Power-On Recall of Wiper Position from Nonvolatile Memory 22k End-to-End Resistance 128 Tap Positions 5ppm/C Ratiometric Temperature Coefficient 1.5A (max) Standby Supply Current +2.7V to +5.25V Single Supply Operation 80,000 Wiper Store Cycles 50-Year Wiper Data Retention
MAX5128
Applications
VCOM Adjustment for LCD Panels Backlight Adjustment LED Bias Adjustment Power-Supply Modules Fiber-Module Bias Setting Bias Setting for Radios Portable Consumer Electronics
PART MAX5128ELA
Ordering Information
TEMP RANGE PINPACKAGE TOP MARK AAF PKG CODE L822-1
-40C to +85C 8 DFN
Functional Diagram
H VCC GND
POR 7-BIT NV MEMORY 7 128-POSITION DECODER 128 TAPS W
L UP DN SERIAL INTERFACE 7
MAX5128
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
ABSOLUTE MAXIMUM RATINGS
VCC to GND ...........................................................-0.3V to +6.0V UP and DN to GND ....................................-0.3V to (VCC + 0.3V) H, L, and W to GND....................................-0.3V to (VCC + 0.3V) Maximum Continuous Current into H, L, and W ..............0.5mA Maximum Continuous Current into All Other Pins ............50mA Continuous Power Dissipation (TA = +70C) 8-Pin DFN (derate 4.7mW/C above +70C) ........376.5mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +5.25V, H = VCC, L = GND, TA = -40C to +85C. Typical values are at VCC = +5.0V, TA = +25C, unless otherwise noted.) (Note 1)
PARAMETER Resolution Integral Nonlinearity Differential Nonlinearity End-to-End Resistance Temperature Coefficient Ratiometric Resistance Temperature Coefficient Full-Scale Error Zero-Scale Error Integral Nonlinearity Differential Nonlinearity Wiper Resistance Wiper Capacitance End-to-End Resistance DIGITAL INPUTS (UP, DN) 3.4V VCC 5.25V Input-High Voltage (Note 5) Input-Low Voltage Input Leakage Current Input Capacitance DYNAMIC CHARACTERISTICS Wiper -3dB Bandwidth THD Plus Noise f3dB THD+N (Note 6) VH = 0.3VRMS, f = 1kHz, wiper set to midscale 400 0.02 kHz % VIH VIL IIN CIN 5 2.7V VCC < 3.4V (Note 5) 2.4 0.7 x VCC
0.8
SYMBOL N INL DNL TCR (Note 2) (Note 2)
CONDITIONS
MIN 7
TYP
MAX
UNITS Bits
DC PERFORMANCE (voltage-divider mode) 1.0 1.0 50 5 FSE ZSE INL DNL RW CW RHL 16 (Note 3) (Note 3) (Note 4) 0.6 20 22 27 -3 0 0 +2 1.75 1 0.8 LSB LSB ppm/C ppm/C LSB LSB LSB LSB k pF k
DC PERFORMANCE (variable-resistor mode)
DC PERFORMANCE (resistor characteristics)
V V A pF
1
2
_______________________________________________________________________________________
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package
ELECTRICAL CHARACTERISTICS (continued)
(VCC = +2.7V to +5.25V, H = VCC, L = GND, TA = -40C to +85C. Typical values are at VCC = +5.0V, TA = +25C, unless otherwise noted.) (Note 1)
PARAMETER Data Retention Endurance POWER SUPPLY Supply Voltage Average Programming Current Peak Programming Current Standby Current VCC IPG IPK ICC During nonvolatile write only; digital inputs = VCC or GND During nonvolatile write only; digital inputs = VCC or GND Digital inputs = VCC or GND, TA = +25C 2.70 220 4 0.5 1.5 5.25 400 V A mA A SYMBOL TA = +85C TA = +25C TA = +85C CONDITIONS MIN TYP 50 80,000 50,000 MAX UNITS Years Stores
MAX5128
NONVOLATILE MEMORY RELIABILITY
TIMING CHARACTERISTICS
(VCC = +2.7V to +5.25V, H = VCC, L = GND, TA = -40C to +85C. Typical values are at VCC = +5.0V, TA = +25C, unless otherwise noted.) (See Figures 1, 2, 3, and 4).
PARAMETER ANALOG SECTION Wiper Settling Time DIGITAL SECTION UP or DN Pulse-Width High UP or DN Pulse-Width Low UP or DN Glitch Immunity UP Fall to DN Rise Setup or DN Fall to UP Rise Setup Before Entering NVM-Write Mode, UP Fall to UP Rise UP Rise to DN Rise Setup when Entering NVM-Write UP Fall to DN Fall Hold or DN Fall to UP Fall Hold during NVMWrite tPWH tPWL tIMMU tMS1 tMS2 tWS 80 80 20 80 80 80 ns ns ns ns ns ns tS (Note 7) 500 ns SYMBOL CONDITIONS MIN TYP MAX UNITS
tWH
0
ns
_______________________________________________________________________________________
3
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
TIMING CHARACTERISTICS (continued)
(VCC = +2.7V to +5.25V, H = VCC, L = GND, TA = -40C to +85C. Typical values are at VCC = +5.0V, TA = +25C, unless otherwise noted.) (See Figures 1, 2, 3, and 4).
PARAMETER NVM-Write Mode Pulse-Width High Write NV Register Busy Time Power-Up Settling Time SYMBOL tWP tBUSY tACC (Note 8) 2 CONDITIONS MIN 80 14 TYP MAX UNITS ns ms s
Note 1: All devices are production tested at TA = +25C and are guaranteed by design for TA = -40C to +85C. Note 2: The DNL and INL are measured with the potentiometer configured as a voltage-divider with H = VCC and L = GND. The wiper terminal is unloaded and measured with a high input-impedance voltmeter. Note 3: The DNL and INL are measured with the potentiometer configured as a variable resistor. H is unconnected and L = GND. For the +5V condition, the wiper terminal is driven with a source current of 200A and for the +2.7V condition, the wiper terminal is driven with a source current of 100A. Note 4: The wiper resistance is measured using the source currents given in Note 3. Note 5: The device draws higher supply current when the digital inputs are driven with voltages between (VCC - 0.5V) and (GND + 0.5V). See Supply Current vs. Digital Input Voltage in the Typical Operating Characteristics. Note 6: Wiper at midscale with a 10pF load, L = GND, an AC source is applied to H, and the output is measured as 3dB lower than the DC W/H value in dB. Note 7: Wiper-settling time is the worst-case 0 to 50% rise time measured between consecutive wiper positions. H = VCC, L = GND, and the wiper terminal is unloaded and measured with a 10pF oscilloscope probe. See the Tap-to-Tap Switching Transient in the Typical Operating Characteristics section. Note 8: Power-up settling time is measured from the time VCC = 2.7V to the wiper settling to 1 LSB of the final value.
4
_______________________________________________________________________________________
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
Typical Operating Characteristics
(VCC = +5.0V, TA = +25C, unless otherwise noted.)
INTEGRAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER)
MAX5128 toc01
INTEGRAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER)
MAX5128 toc02
INTEGRAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER)
0.10 0.08 0.06 INL (LSB) 0.04 0.02 0 -0.02 -0.04 -0.06 VCC = 2.7V, TA = +85C
MAX5128 toc03 MAX5128 toc09 MAX5128 toc06
0.12 0.10 0.08 0.06 INL (LSB) 0.04 0.02 0 -0.02 -0.04 -0.06 0 12 24 36 48 60 72 84 96 108 120 CODE VCC = 2.7V, TA = -40C
0.12 0.10 0.08 0.06 INL (LSB) 0.04 0.02 0 -0.02 -0.04 -0.06 0 12 24 36 48 60 72 84 96 108 120 CODE VCC = 2.7V, TA = +25C
0.12
0
12 24 36 48 60 72 84 96 108 120 CODE
DIFFERENTIAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER)
MAX5128 toc04
DIFFERENTIAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER)
MAX5128 toc05
DIFFERENTIAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER)
0.010 0.008 0.006 0.004 DNL (LSB) 0.002 0 VCC = 2.7V, TA = +85C
0.010 0.008 0.006 0.004 DNL (LSB) 0.002 0
VCC = 2.7V, TA = -40C
0.010 0.008 0.006 0.004 DNL (LSB) 0.002 0
VCC = 2.7V, TA = +25C
-0.002 -0.004 -0.006 -0.008 -0.010 0 12 24 36 48 60 72 84 96 108 120 CODE
-0.002 -0.004 -0.006 -0.008 -0.010 0 12 24 36 48 60 72 84 96 108 120 CODE
-0.002 -0.004 -0.006 -0.008 -0.010 0 12 24 36 48 60 72 84 96 108 120 CODE
INTEGRAL NONLINEARITY vs. CODE (VARIABLE RESISTOR)
MAX5128 toc07
INTEGRAL NONLINEARITY vs. CODE (VARIABLE RESISTOR)
MAX5128 toc08
INTEGRAL NONLINEARITY vs. CODE (VARIABLE RESISTOR)
1.5 VCC = 2.7V, TA = +85C 1.0 0.5 INL (LSB) 0 -0.5 -1.0 -1.5
1.5 VCC = 2.7V, TA = -40C 1.0 0.5 INL (LSB) 0 -0.5 -1.0 -1.5 0 12 24 36 48 60 72 84 96 108 120 CODE
1.5 VCC = 2.7V, TA = +25C 1.0 0.5 INL (LSB) 0 -0.5 -1.0 -1.5 0 12 24 36 48 60 72 84 96 108 120 CODE
0 12 24 36 48 60 72 84 96 108 120 CODE
_______________________________________________________________________________________
5
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
Typical Operating Characteristics (continued)
(VCC = +5.0V, TA = +25C, unless otherwise noted.)
DIFFERENTIAL NONLINEARITY vs. CODE (VARIABLE RESISTOR)
MAX5128 toc10
DIFFERENTIAL NONLINEARITY vs. CODE (VARIABLE RESISTOR)
MAX5128 toc11
DIFFERENTIAL NONLINEARITY vs. CODE (VARIABLE RESISTOR)
0.20 0.15 0.10 VCC = 2.7V, TA = +85C
MAX5128 toc12
0.20 VCC = 2.7V, TA = -40C 0.15 0.10 DNL (LSB)
0.20 0.15 0.10 DNL (LSB)
VCC = 2.7V, TA = +25C
0.25
DNL (LSB) 0 12 24 36 48 60 72 84 96 108 120 CODE
0.05 0 -0.05 -0.10 -0.15 -0.20 0 12 24 36 48 60 72 84 96 108 120 CODE
0.05 0 -0.05 -0.10 -0.15 -0.20
0.05 0 -0.05 -0.10 -0.15 -0.20 -0.25 0 12 24 36 48 60 72 84 96 108 120 CODE
RATIOMETRIC TEMPERATURE COEFFICIENT vs. CODE (VOLTAGE-DIVIDER)
MAX5128 toc13
TEMPERATURE COEFFICIENT vs. CODE (VARIABLE RESISTOR)
800 700 600 TCVR (ppm/C) 500 400 300 200 100 0 -100 TA = -40C TO +85C VCC = 2.7V
MAX5128 toc14
160 140 RATIOMETRIC TEMPCO (ppm/C) 120 100 80 60 40 20 0 -20 0 12 24 36 48 60 72 84 96 108 120 CODE VCC = 2.7V TA = -40C TO +85C
900
0 12 24 36 48 60 72 84 96 108 120 CODE
END-TO-END RESISTANCE (RHL) % CHANGE vs. TEMPERATURE
MAX5128 toc15
STANDBY SUPPLY CURRENT vs. TEMPERATURE
MAX5128 toc16
1.0 END-TO-END RESISTANCE CHANGE (%) 0.8 0.6 0.4
1.5
1.2
0 -0.2 -0.4 -0.6 -0.8 -1.0 -40 -15 10 35 60 85 TEMPERATURE (C)
IDD (A)
0.2
0.9 VCC = 5.25V 0.6 VCC = 2.7V VCC = 3.3V
0.3
0 -40 -15 10 35 60 85 TEMPERATURE (C)
6
_______________________________________________________________________________________
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
Typical Operating Characteristics (continued)
(VCC = +5.0V, TA = +25C, unless otherwise noted.)
SUPPLY CURRENT vs. DIGITAL INPUT VOLTAGE
MAX5128 toc17
WIPER RESISTANCE vs. TEMPERATURE
VCC = 5V WIPER = MIDSCALE 800
MAX5128 toc18
WIPER RESPONSE vs. FREQUENCY
-2 -4 -6 GAIN (dB) VCC = 5V WIPER = MIDSCALE
MAX5128 toc19
1000 VCC = 5V 100 IDD (A)
1000
0
RW ()
600
-8 -10 -12
10
400 1
200
-14 -16
0.1 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 DIGITAL INPUT VOLTAGE (V)
0 -40 -15 10 35 60 85 TEMPERATURE (C)
-18 0.1 1 10 FREQUENCY (kHz) 100 1000
THD+N vs. FREQUENCY
VCC = 5V WIPER = MIDSCALE FILTER BANDWIDTH = 80kHz
MAX5128 toc20
TAP-TO-TAP SWITCHING TRANSIENT
MAX5128 toc21
10
1
UP 2V/div
THD+N (%)
0.1
0.01 H = VCC L = GND FROM MIDSCALE CW = 20pF 0.1 1 10 100 1s/div FREQUENCY (kHz) VW 20mV/div AC-COUPLED
0.001
0.0001
WIPER RESISTANCE vs. CODE
MAX5128 toc22
MIDSCALE WIPER TRANSIENT AT POWER-ON
600 500 400 RW () 300 200 100 0 0 12 24 36 48 60 72 84 96 108 120 CODE
MAX5128 toc23
VCC 2V/div
OUTPUT W 2V/div
10s/div
_______________________________________________________________________________________
7
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
Pin Description
PIN 1 2 3 4 5 6 7 8 NAME VCC H W L GND DN UP N.C. FUNCTION Power Supply. Bypass VCC with a 0.1F capacitor to GND as close to the device as possible. For proper operation, limit the supply voltage slew rate to 10s. High Terminal. The voltage at H can be higher than or lower than the voltage at L. Current can flow into or out of H. Wiper Terminal Low Terminal. The voltage at L can be higher than or lower than the voltage at H. Current can flow into or out of L. Ground Down Input Up Input No Connection. Not internally connected.
tPWH
NVM WRITE tPWL tMS1
UP tPWL DN tMS1 tWS tWH tPWH tWP
Figure 1. Digital-Interface Timing Diagram
Detailed Description
The MAX5128 nonvolatile, single, linear-taper, digital potentiometer performs the function of a mechanical potentiometer or variable resistor, but replaces the mechanics with a simple 2-wire digital interface. This device features 128 taps and 22k end-to-end resistance with a 5ppm/C ratiometric temperature coefficient. The MAX5128 operates from a +2.7V to +5.25V power supply and consumes only 0.5A (typ) of standby supply current. The MAX5128 includes an integrated nonvolatile memory that recalls the stored wiper position of the digital potentiometer. A simple 2-wire up/down interface programs the wiper positions.
Analog Circuitry
The MAX5128 consists of a resistor array with 127 resistive elements; 128 tap points along the resistor string between H and L are accessible to the wiper, W. Select the wiper tap point by programming the potentiometer through the 2-wire (UP, DN) interface. The MAX5128 features power-on reset circuitry that loads the wiper position from the nonvolatile memory at power-up. The nonvolatile memory is programmed to midscale at the factory.
8
_______________________________________________________________________________________
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
t PWH t PWL t MS2 NVM WRITE t BUSY
UP t WP
DN t WS t WH
Figure 2. Digital-Interface Timing Diagram with tBUSY
tBUSY
UP
DN WIPER DECREMENTS
WIPER INCREMENTS
WIPER DECREMENTS
NVM WRITE
NVM WRITE
WIPER INCREMENTS
Figure 3. Digital-Interface Command Diagram
Digital Interface
The MAX5128 features a 2-wire interface consisting of two logic inputs (UP and DN). Logic inputs UP and DN control the wiper position and program the position to the nonvolatile memory. Transition UP from high to low with DN low to increment the wiper position. Transition DN from high to low with UP low to decrement the wiper position (see Figures 1, 2, and 3). When the wiper decrements, it decreases the resistance between W and L (and it increases the resistance between H and W). To program the nonvolatile memory, force UP high, then force DN high, and then transition either input (UP/DN) from high to low (see Figure 3). The wiper performs a make-before-break transition, ensuring that an open circuit during a transition from one resistor tap to another does not occur. The wiper does not wrap around when it reaches either end of the resistor array (max/min). Additional transition commands in the direction of the end point do not change the tap position.
The logic inputs also feature pulse glitch immunity (20ns) to protect the wiper from transitioning due to glitches (see Figure 4). When using the MAX5128 with a momentary contact switch, use the MAX6817 to debounce the logic inputs (UP/DN) (see Figure 5). Write NV Register The internal EEPROM consists of a 7-bit nonvolatile memory that retains the value written to it even after power-down. To program the nonvolatile memory, force UP high, then force DN high, and then transition either input (UP/DN) from high to low. A nonvolatile write requires a busy time of 14ms (max). During the busy time, any nonvolatile write requests are ignored as well as requests to increment or decrement the wiper position. Upon power-up, the wiper returns to the position stored in the nonvolatile register. The MAX5128 features a factory-default wiper position of midscale.
_______________________________________________________________________________________
9
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
tIMMU tIMMU UP
DN
tIMMU
tIMMU
PULSES WITH WIDTHS LESS THAN tIMMU ARE IGNORED.
Figure 4. Glitch-Immunity Timing Diagram
Standby Mode
The MAX5128 operates in standby mode while the serial interface is inactive. Programming the MAX5128 increases the average operating current to 400A (max). When in standby mode, the static supply current reduces to less than 0.5A (typ).
5V VCC MECHANICAL SWITCH IN1
MAX6817 MAX5128
5V VCC OUT1 UP
VCC
H
Power-Up
Upon power-up, the MAX5128 updates the wiper position with the data stored in the nonvolatile memory. This initialization period takes 2s (typ). For proper operation, limit the supply voltage slew rate to 10s.
MECHANICAL SWITCH
VCC
W
OUT2 IN2 GND
DN
Applications Information
Use the MAX5128 for applications requiring digitally controlled adjustable resistance or voltage, such as LCD contrast control (where voltage biasing adjusts the display contrast), or DC-DC converters with adjustable outputs. The 22k end-to-end resistance is divided into 128 tap points of 172 each. Use the MAX5128 in a voltage-divider or variable-resistor configuration.
GND L
Figure 5. Debouncing the MAX5128's Digital Inputs
VCOM Generator
Figure 6 shows an application using the MAX4238 and the MAX5128 to generate the VCOM voltage for a LCD panel. Adjusting the resistor value of the MAX5128 changes the VCOM voltage. Adjusting the VCOM voltage changes the contrast for the LCD panel.
potentiometer configuration to allow the DC-DC converter's output to exceed the supply voltage range of the MAX5128. The floating potentiometer configuration increases the output voltage range and increases the precision of the output voltage adjustment range.
LED Bias Adjustment
Figure 9 shows a LED bias adjustment application using a MAX5128 to set the current of the LEDs that the MAX1574 drives. Use the MAX5128 for an adjustable LED current drive of 10mA to 60mA.
DC-DC Converter Applications
Figures 7 and 8 show two applications using the MAX5128 to adjust the output voltage of a DC-DC converter. Figure 7 shows the MAX5128 in the grounded potentiometer configuration. Figure 8 shows the MAX5128 in a floating potentiometer configuration. The grounded potentiometer configuration forces the output voltage range of the DC-DC converter to fall within the supply voltage range of the MAX5128. Use the floating
10
Chip Information
PROCESS: BiCMOS
______________________________________________________________________________________
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
+3.3V 15k 120k +5V H 0.1F TIMING-CONTROL-IC OUTPUT SIGNAL 10k W 22k
MAX5128
MAX4238
L
VCOM 51k
+3.3V 27k
36k
0.1F
Figure 6. VCOM Generator Circuit for LCD Panels
VOUT = 2V TO 5.25V LX OUT H
MAX1722
VIN = 0.8V TO VOUT FB BATT
MAX5128
W
GND L
Figure 7. DC-DC Converter Using a Grounded Potentiometer
______________________________________________________________________________________
11
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package MAX5128
SW
LX
VOUT = VCC TO 28V
MAX8574
VCC = 2.7V TO 5.5V VCC FB W
H
MAX5128
SHDN
GND
L
Figure 8. DC-DC Converter Using a Floating Potentiometer
Pin Configuration
CN VIN = 2.7V TO 5.5V CP
TOP VIEW
N.C. UP 7 DN 6 GND 5
OUT
IN
8
MAX1574
LED1 H LED2 SET
MAX5128
MAX5128
W
1 VCC
LED3
2 H
3 W
4 L
2mm x 2mm DFN
L
GND
Figure 9. LED Bias Adjustment Using the MAX5128
12
______________________________________________________________________________________
128-Tap, Nonvolatile, Linear-Taper Digital Potentiometer in 2mm x 2mm DFN Package
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
6, 8, 10L UDFN.EPS
MAX5128
D
A
e
b
N
XXXX XXXX XXXX
SOLDER MASK COVERAGE
E
PIN 1 0.10x45
L
PIN 1 INDEX AREA SAMPLE MARKING 7 1 A A
L1
(N/2 -1) x e)
C L
C L
b A A2 A1
L e
EVEN TERMINAL
L e
ODD TERMINAL
PACKAGE OUTLINE, 6, 8, 10L uDFN, 2x2x0.80 mm
-DRAWING NOT TO SCALE-
21-0164
A
1
2
COMMON DIMENSIONS SYMBOL A A1 A2 D E L L1 MIN. 0.70 0.15 0.020 1.95 1.95 0.30 NOM. 0.75 0.20 0.025 2.00 2.00 0.40 0.10 REF. MAX. 0.80 0.25 0.035 2.05 2.05 0.50
PACKAGE VARIATIONS PKG. CODE L622-1 L822-1 L1022-1 N 6 8 10 e 0.65 BSC 0.50 BSC 0.40 BSC b 0.300.05 0.250.05 0.200.03 (N/2 -1) x e 1.30 REF. 1.50 REF. 1.60 REF.
PACKAGE OUTLINE, 6, 8, 10L uDFN, 2x2x0.80 mm
-DRAWING NOT TO SCALE-
21-0164
A
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 (c) 2006 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.
Boblet

▲Up To Search▲

Price & Availability of MAX5128

	To Download MAX5128 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .